Insulation Company in Burbank, CA
Blown in insulation is the most common retrofit we install in Burbank, and for good reason: the city’s 1940s and 1950s tract homes and bungalows were built when energy was cheap and attics were an afterthought. Many of those original attics now hold three inches of settled, compressed fiberglass, which does almost nothing against Burbank summers that routinely cross 100°F. Even Air Insulation has served Burbank since 2018, and we match the insulation method to the house, not the other way around. Call us at (855) 362-0195 for a straight answer on what your attic actually needs.
Why Burbank Homes Are Different
Burbank sits in the eastern San Fernando Valley, where summer heat is the real enemy. Attic temperatures in older Burbank homes can spike past 140°F on a July afternoon, and that heat radiates down through ceilings for hours after sunset. Homes in the flatlands between Magnolia Boulevard and Victory Boulevard, and up into the Verdugo foothills, were mostly built between 1940 and 1960 with minimal or degraded attic insulation and uninsulated stucco-over-wood-frame walls. Single-pane aluminum windows are common, so air leaks compound the insulation problem.
The other factor is noise. Burbank sits directly under the Hollywood Burbank Airport approach paths, and thousands of homes in the 91505 and 91506 ZIP codes also absorb freeway sound from the 5 and the 134. For a lot of Burbank homeowners, dense-pack wall insulation and properly air-sealed attics matter as much for cutting aircraft and traffic noise as they do for energy savings. That dual pressure – extreme attic heat plus aviation noise – is not something you see paired this way in most Valley cities, and it changes how we spec insulation here.
Stucco exteriors are near-universal on Burbank’s older homes, which means wall cavities are often the only retrofit path for whole-house comfort. And because so many homes still have knob-and-tube-era framing, we see wall voids and irregular joist spacing that make loose-fill and dense-pack methods a better fit than batt work in a lot of cases.
Our Main Burbank Services
Most Burbank homeowners call us about one of two things: an attic that’s cooking the house all summer, or rooms that stay warm in winter and hot in summer no matter what the thermostat says. Here’s how each plays out in Burbank specifically.
Attic Insulation in Burbank
Burbank attics in postwar ranch homes and bungalows are usually accessible but under-insulated, often with old fiberglass batts that have compacted to R-11 or less. Cooling load is the dominant problem here: a poorly insulated attic can add hundreds of dollars to a Burbank summer electric bill. We see the biggest wins when we air-seal the attic floor first, then bring the assembly up to an appropriate R-value with blown-in or batt material matched to the home’s framing and venting. For houses near the airport, attic insulation also cuts a measurable amount of overhead aircraft noise. Read more at Attic Insulation in Burbank.
Spray Foam Insulation in Burbank
Spray foam is not automatically the answer for every Burbank home, but it earns its cost in specific situations: unvented attics, rooms directly under a flat roof, or rim-joist and band-joist air leaks that let hot valley air pour into the house. We carry both Icynene and Demilec product lines, which gives us open-cell and closed-cell options for different moisture and structural conditions. Closed-cell also helps with aircraft noise in roof assemblies where fiberglass would do little. Details are on Spray Foam Insulation in Burbank.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Blown In Insulation in Burbank
Blown in insulation is the retrofit workhorse for Burbank’s mid-century housing stock. Loose-fill cellulose or fiberglass is blown into attics and wall cavities through small access holes, which means we can insulate a 1950s stucco home without tearing out drywall, something batt insulation often can’t do in older framing. In a Burbank attic, a properly installed loose-fill layer of cellulose can cut ceiling heat transfer dramatically, which is the single most effective cooling-load reduction most of these homes can get. It’s also the method we reach for most often for dense-pack wall retrofits under the airport approach paths, where blocking aircraft and freeway noise matters as much as thermal performance. For more on how blown in works and where it fits, see our Blown In Insulation hub page.
Cellulose Insulation
Signs you need it
Your attic insulation is thin, settled, or matted down below the tops of the ceiling joists, or your upstairs rooms spike 10 to 15 degrees hotter than the rest of the house on summer afternoons.
What it costs in Burbank
Blown-in cellulose in Burbank typically runs $1.10 to $2.30 per square foot depending on depth, access, and whether we air-seal the attic floor first.
How we do it
We air-seal ceiling penetrations, mark the target depth, run a hose into the attic or wall cavity, and blow in GreenFiber cellulose to the coverage level your ceiling area and R-value goal require.
Blown In Attic Insulation
Signs you need it
Your attic has fiberglass batts from the 1960s or 1970s that look intact but measure under R-19, or you can feel heat radiating from the ceiling on hot evenings after the sun goes down.
What it costs in Burbank
Blown-in attic insulation for a typical Burbank ranch runs $1,200 to $3,500 total, with the spread driven by attic square footage, target R-value, and air-sealing work.
How we do it
We remove or level the existing material as needed, seal top plates, can lights, and plumbing penetrations, then blow loose-fill insulation to an even, measured depth across the entire attic floor.
Blown In Cellulose Insulation
Signs you need it
You want higher recycled content and better sound-dampening than fiberglass offers, or you’re insulating walls in an older Burbank home where dense-packing is the only practical retrofit path.
What it costs in Burbank
Dense-pack wall cellulose in Burbank generally runs $2.00 to $3.50 per square foot of wall area, including access-hole drilling and repairs.
How we do it
We drill small access holes through stucco or interior drywall, dense-pack GreenFiber cellulose into each stud bay at pressure, then patch and texture the holes to match.
Blown In Fiberglass Insulation
Signs you need it
You need attic coverage on a tighter budget or you’re topping off areas where blown fiberglass already exists and you want a consistent loose-fill material.
What it costs in Burbank
Blown-in fiberglass in Burbank attics typically ranges from $1.00 to $2.00 per square foot installed, depending on depth and access.
How we do it
We prepare the attic floor, install depth markers, and blow fiberglass loose-fill to the specified R-value, working around existing framing and keeping soffit vents clear.
What Blown In Insulation Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Blown-in attic insulation (full retrofit) | $1,200 – $3,500 |
| Blown-in cellulose (per sq ft) | $1.10 – $2.30 |
| Dense-pack wall cellulose (per sq ft of wall) | $2.00 – $3.50 |
Is blown in insulation worth it in Burbank?
The ceiling is your home’s biggest heat-gain surface in a Burbank summer, and loose-fill insulation directly addresses that. Most Burbank retrofits pay back in three to five years through lower cooling bills, and the noise reduction under flight paths is immediate. Call (855) 362-0195 for a Burbank-specific number.
How long does blown in insulation last in a Burbank attic?
Cellulose and fiberglass loose-fill both hold their R-value for decades unless they get wet or are disturbed. The bigger issue in Burbank attics is settling, which is why we install to a slightly higher depth spec than the label R-value assumes.
Brands We Service in Burbank
We install products from the brands that fit Burbank’s specific conditions: CertainTeed for fiberglass loose-fill and batt work, Icynene and Demilec for spray foam, and GreenFiber for recycled-content cellulose. Common materials are stocked locally, and specialty products usually arrive within days. See our brands for the full lineup.
Pricing for Insulation Company in Burbank, CA
| Service | Typical range in Burbank |
|---|---|
| Blown-in attic insulation (full retrofit) | $1,200 – $3,500 |
| Blown-in cellulose (per sq ft) | $1.10 – $2.30 |
| Blown-in fiberglass (per sq ft) | $1.00 – $2.00 |
| Dense-pack wall cellulose (per sq ft of wall) | $2.00 – $3.50 |
| Spray foam insulation (per sq ft, open-cell) | $0.50 – $2.00 |
| Spray foam insulation (per sq ft, closed-cell) | $1.00 – $3.50 |
| Spray foam rim joist (per linear ft) | $4.00 – $8.00 |
| Spray foam crawl space walls (per sq ft) | $1.50 – $3.00 |
| Attic air sealing (flat entry fee) | $250 – $600 |
| Attic insulation removal (per sq ft) | $0.75 – $2.00 |
| Batt insulation (per sq ft) | $0.80 – $1.60 |
| Radiant barrier (per sq ft) | $0.50 – $1.00 |
Two things push Burbank prices up more than anything else: attic access that is tight or obstructed by older framing, and the need for air sealing before insulation goes in. We quote a fixed, upfront price before any work begins, so the number you approve is the number you pay.
Neighborhoods We Serve in Burbank
We work across Burbank’s flatland tract neighborhoods and the hillside streets alike, from the Magnolia Park district and the Chandler Bike Path corridor up to the Verdugo foothills and the streets around Brace Canyon Park. Typical first-visit scheduling runs within a week for most Burbank ZIP codes.
- Magnolia Park
- Rancho Adjacent
- Verdugo Foothills
- Brace Canyon Park area
- Northwest Burbank (91505)
Service Area – Cities Near Burbank
Even Air Insulation serves Burbank and the surrounding San Fernando Valley and northeast Los Angeles communities. If you’re nearby, we also work in Glendale, CA, North Hollywood, CA, Studio City, CA, and Universal City, CA. Same-week scheduling is generally available across this service area.
Serving Burbank, CA — Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Insulation Company in Burbank
Most insulation retrofits in Burbank do not require a permit, since they fall under standard residential weatherization work. If your project involves structural changes or new construction, the city may require documentation, and we will tell you upfront before work begins.
For most Burbank ZIP codes, including 91505, 91506, and 91507, we can schedule a first visit within three to five business days. Emergency attic work after a leak or animal intrusion sometimes gets a same-week slot. Call (855) 362-0195 and we will give you a straight answer.
Dense-pack wall insulation is installed through small drilled holes, typically one to two inches across, that we patch and texture to match your stucco finish. Done correctly, the repair is nearly invisible, and the process does not weaken the stucco assembly itself. We walk through the exact access points with you before drilling anything.
If your Burbank home is fighting the summer heat or the airport noise, call Even Air Insulation at (855) 362-0195 for a free estimate. We will inspect what is already in your attic and walls, tell you what it will take to fix it, and give you an upfront price for the work. Visit our home page to see the full range of what we do across the Valley.
What happens when you call
- 1A real person answersNo phone trees — talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 60-minute.
- 4You approve before work beginsNothing starts until you say go.
What Burbank Customers Say
"Attic was at maybe R-11 from the 1970s and blown in over the top would have just buried the problem. They removed the old material, air sealed the top plates and penetrations first, then blew in to R-49. The upstairs is a completely different house in August."
— Emily Gallagher"Found and sealed a gap around the chimney chase that was basically an open chimney to the attic."
— Luis Garcia"Plastic laid from the front door to the attic hatch and they vacuumed the hallway afterward."
— Andres Vargas